FF01-440/521/607/700-25

440/521/607/700 nm BrightLine 四通带带通滤光片

  • 透过率Tavg > 90%, 420 – 460 nm; Tavg > 90%, 510.5 – 531.5 nm; Tavg > 90%, 590 – 624 nm & Tavg > 90%, 677.5 – 722.5 nm
  • 中心波长 440 nm, 521 nm, 607 nm & 700 nm; GMBW带宽 40 nm, 21 nm, 34 nm & 45 nm

Description

440/521/607/700 nm BrightLine 四通带带通滤光片

滤光片型号:FF01-440/521/607/700-25

Theoretical Spectrum for Part Number: FF01-440/521/607/700-25

FF01-440/521/607/700-25插图

FF01-440/521/607/700-25带通滤光片透过率曲线,Semrock

440/521/607/700 nm BrightLine 四通带带通滤光片,25 mm直径,3.5 mm厚度

采用Semrock单基板结构的单个多波段荧光带通滤光片。这些滤光片具有极高的透过率、陡峭且轮廓分明的边缘,以及通带之间的出色阻断。全薄膜硬质膜层结构,性能和可靠性十分优异。

滤光片参数:

Optical Specifications Value
Transmission Band 1 Tavg > 90% 420 – 460 nm
Transmission Band 2 Tavg > 90% 510.5 – 531.5 nm
Transmission Band 3 Tavg > 90% 590 – 624 nm
Transmission Band 4 Tavg > 90% 677.5 – 722.5 nm
Blocking Band 1 ODavg > 5 275 – 381.5 nm
Blocking Band 2    ODavg > 8 381.5 – 392.5 nm (Design specification – measurements are noise-floor limited).
Blocking Band 3    ODavg > 8 475 – 495 nm (Design specification – measurements are noise-floor limited).
Blocking Band 4    ODavg > 8 547 – 572 nm (Design specification – measurements are noise-floor limited)
Blocking Band 5    ODavg > 8 643 – 656 nm (Design specification – measurements are noise-floor limited)
Blocking Band 6 ODavg > 5 744 – 925 nm
Center Wavelength 1 440 nm
Center Wavelength 2 521 nm
Center Wavelength 3 607 nm
Center Wavelength 4 700 nm
Guaranteed Minimum Bandwidth 1 40 nm
Guaranteed Minimum Bandwidth 2 21 nm
Guaranteed Minimum Bandwidth 3 34 nm
Guaranteed Minimum Bandwidth 4 45 nm
FWHM Bandwidth 1 (nominal) 44 nm
FWHM Bandwidth 2 (nominal) 26 nm
FWHM Bandwidth 3 (nominal) 40 nm
FWHM Bandwidth 4 (nominal) 52 nm
General Filter Specifications Value
Angle of Incidence 0 ± 5 degrees
Cone Half-angle 7 degrees
Optical Damage Rating Testing has proven to show no signs of degradation when exposed to at least 6.0 W of power from an unfiltered xenon arc lamp over a 25 mm diameter (corresponding to 1.2 W/cm2) for over 500 hours.
Physical Filter Specifications    Value
Transverse Dimensions (diameter) 25 mm
Transverse Tolerance + 0.0 / – 0.1 mm
Filter Thickness (mounted) 3.5 mm
Filter Thickness Tolerance (mounted) ± 0.1 mm
Clear Aperture ≥ 22 mm
Scratch-Dig 60-40
Filter Thickness (unmounted) 2.0 mm
Filter Thickness Tolerance (unmounted) ± 0.1 mm
Orientation Arrow on ring indicates preferred direction of propagation of light

标题

返回顶部